2014 KENWORTH T800 Recalls & Safety Issues
Official recalls, technical service bulletins (TSBs), and safety issues from the National Highway Traffic Safety Administration (NHTSA).
12
Recalls Found
All Recalls
PACCAR Incorporated (PACCAR) is recalling certain 2012-2018 Kenworth T800 and T880 vehicles equipped with Neway ADZ tridem rear suspensions. The brake control airline may be the incorrect size, resulting in an imbalance in the service brake application timing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air brake systems."
NHTSA 17V322000
Consequence: An incorrectly sized airline may lengthen the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy / Corrective Action
Kenworth will notify owners, and dealers will modify the air brake system with updated brake piping, free of charge. The recall began on June 21, 2017. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 17KWB.
PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T270, T370, T440, T470, C500, C540, C550, T660, T800, W900, and 963 trucks manufactured November 1, 2010, to April 6, 2015. In the affected trucks, water may leak into the wiper motor.
NHTSA 15V271000
Consequence: As water leaks in, the wiper may cease to function on the 'intermittent' setting, reducing the driver's visibility and increasing the risk of a crash. Additionally, the water may cause corrosion which, over time, may result in an electrical short, increasing the risk of a fire.
Remedy / Corrective Action
PACCAR is still developing and testing a remedy. The recall is expected to begin in July 2015. An interim letter was sent to owners on July 2, 2015. The recall began on September 2, 1015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWF.
PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.
NHTSA 15V309000
Consequence: If engine oil comes into contact with a hot surface, there is an increased risk of a fire.
Remedy / Corrective Action
Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.
PACCAR Inc, is recalling certain model year 2014-2015 Kenworth T440, T660, T800, and W900 tractor trailers manufactured January 23, 2013, through February 4, 2014, and certain model year 2014-2015 Peterbilt 320, 365, 382, 384 tractor trailers manufactured January 21, 2013, through February 5, 2014, and equipped with certain Cummins Westport Model ISL G and ISX12 G engines. Condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor.
NHTSA 14V086000
Consequence: The improper operation of the sensor could induce elevated exhaust temperatures or flames from the exhaust pipe, increasing the risk of a vehicle fire or burn injury to a person near the exhaust pipe.
Remedy / Corrective Action
PACCAR will notify owners, and authorized Cummins service facilities will upload a new ECM calibration, free of charge. The recall began on April 12, 2014. Customers may contact PACCAR at 1-425-468-7400. Paccar's recall numbers associated with this campaign are 14KWG (Kenworth), and 214-C (Peterbilt).
PACCAR Incorporated (PACCAR) is recalling certain model year 2014 and 2015 Kenworth T660, T680, and T800 trucks manufactured January 29, 2013, to April 2, 2014, and 2013 Peterbilt 587 trucks manufactured on August 8, 2012. The affected trucks are built with a driveshaft that may not transmit power to the wheels due to weld failure from corrosion.
NHTSA 15V310000
Consequence: If the weld fails causing a loss of power to the rear wheels, the vehicle operator may be unable to move the vehicle, or may experience deceleration if the vehicle is in motion, increasing the risk of a vehicle crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will replace the defective driveshafts, free of charge. The recall began on July 15, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, or Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 15KWJ and 515-H.
PACCAR is recalling certain model year 2007-2014 Kenworth T800 and W900 trucks manufactured March 22, 2006, through July 15, 2013 and equipped with Primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems."
NHTSA 13V573000
Consequence: Brakes that take longer to apply may lengthen the distance needed to stop the truck, increasing the risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will modify the air brake system, free of charge. The recall began on January 15, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's recall number is 13KWL.
PACCAR Incorporated (Paccar) is recalling certain model year 2014 Kenworth T170, T270, T370, T440, T470, T660, T680, T700, T800, T880, C500 and W900 trucks manufactured July 1, 2013 through September 17, 2013. In the affected vehicles, the plastic housing of the Stop/Tail/Turn (STT) lamp can shrink and allow the light bulb to fall out of the mounted retention ring. As such, the Stop/Tail/Turn light would not be illuminated, and the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) No. 108 "Lamps, Reflective Devices, and Associated Equipment."
NHTSA 13V612000
Consequence: If the stop/tail/turn light is not illuminated, the driver's intentions would not be communicated, which increases the risk of a crash.
Remedy / Corrective Action
Kenworth will notify owners, and dealers will replace the defective STT lamps with new lamps. The recall began on February 4, 2014. Customers may contact Paccar at 1-425-468-7400. Kenworth's number for this recall is 13KWM.
PACCAR is recalling certain model year 2014 Kenworth T470 and T800 trucks manufactured January 1, 2013, through January 22, 2013. A parameter in the Electronic Service Analysis (ESA) tool was mistakenly switched to disable the start-in-gear protection feature. Because of this, the vehicles may be started when the automatic transmission is in gear.
NHTSA 13V244000
Consequence: If the vehicle is started while it is in gear, it may move unexpectedly, increasing the risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners and dealers will correct the ESA parameter, free of charge. The recall began on June 27, 2013. PACCAR's recall number is 13KWH. Owners may contact PACCAR at 1-425-468-7400.
PACCAR is recalling certain model year 2014 Kenworth T170, T270, T370, T470, T660, T680, T800, T880, and W900 trucks manufactured May 6, 2013, through May 17, 2013; and model year 2014 Peterbilt 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, 389K, 567, 579 and 587 trucks manufactured May 1, 2013 through May 17, 2013. An internal defect in the ignition switch causes the starter to engage when a key is partially inserted, before the key is turned.
NHTSA 13V222000
Consequence: Unintended engine startup could cause injury to a person working in the engine compartment. Vehicles with standard transmissions may experience unexpected movement, which may result in personal injury or a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will replace affected ignition switches, free of charge. The recall began on June 14, 2013. Owners may contact Kenworth at 1-425-828-5000 or Peterbilt at 1-940-591-4000. Kenworth's recall campaign number is 13KWF. Peterbilt's recall campaign number is 0513-E.
PACCAR Incorporated (PACCAR) is recalling certain model year 2014 Kenworth T660, T680, T700,T800, T880, W900, T440, T470, T370, T270, T170, C500, and C550 chassis manufactured between August 7, 2013, and October 31, 2013, and Peterbilt 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 chassis manufactured between August 7, 2013, and November 3, 2013, and equipped with IMMI-brand L9 seat belt buckles. When the button is pressed to release the seat belt, the latch plate can become partially engaged with the buckle, making the seat belt difficult to unlatch. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 209, "Seat Belt Assemblies."
NHTSA 14V013000
Consequence: If the latch plate remains partially engaged after the button is pressed, egress from the vehicle could be hindered which would increase the risk of injury in the event of an emergency.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will inspect and replace the seat belt buckles, as necessary, free of charge. The recall began on March 31, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's number for this campaign is 14KWC. Peterbilt's number for this campaign is 114-B.
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."
NHTSA 20V199000
Consequence: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."
NHTSA 24V145000
Consequence: Insufficient air volume can reduce braking performance and increase the risk of a crash.
Remedy / Corrective Action
Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.
Frequently Asked Questions
How many recalls does the 2014 KENWORTH T800 have?
The 2014 KENWORTH T800 currently has 12 recalls according to NHTSA records. All recall information is sourced directly from the National Highway Traffic Safety Administration database.
Are 2014 KENWORTH T800 recalls free to fix?
Yes! All safety recalls for 2014 KENWORTH T800 vehicles must be repaired free of charge by authorized dealers, regardless of vehicle age or mileage. Contact your local KENWORTH dealer to schedule a recall repair.
How do I check if my 2014 KENWORTH T800 has open recalls?
You can check for open recalls by entering your VIN (Vehicle Identification Number) in our VIN decoder tool. The 17-character VIN can be found on your vehicle registration, insurance card, or on the driver's side dashboard visible through the windshield.
Other Years - KENWORTH T800
2025 Recalls
2024 Recalls
2023 Recalls
2022 Recalls
2021 Recalls
2020 Recalls
2019 Recalls
2018 Recalls
2017 Recalls
2016 Recalls
2015 Recalls
2013 Recalls
2012 Recalls
2011 Recalls
2010 Recalls
Other KENWORTH Models
540
542
548CH
C5 Series
C500
C540
C550
K 100E
K100
K260/K360
K270/K370
K3 Series
K300
KS
KT
KW45/KW55
L7 Series
L700
L770
Other Off-Highway
Similar Brands
SETRA
4 models
AUTOCAR
24 models
MAYBACH
2 models
ZNEN
87 models
SUBARU
24 models
JAGUAR
17 models
WHITE
63 models
INTERNATIONAL
473 models
KTM
95 models
FORD
168 models