2016 KENWORTH T800 Recalls & Safety Issues
Official recalls, technical service bulletins (TSBs), and safety issues from the National Highway Traffic Safety Administration (NHTSA).
12
Recalls Found
All Recalls
PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Peterbilt 567 and 579 trucks and 2015-2018 Kenworth T660, T680, T800, T880 and W900 trucks. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."
NHTSA 18V368000
Consequence: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on July 30, 2018. Owners may contact Peterbilt customer service at 1-918-259-3258 or Kenworth customer service at 1-425-828-5000.
PACCAR Incorporated (PACCAR) is recalling certain 2016-2019 Kenworth C500, T660, T800, and W900 vehicles, equipped with 1.9M ISX15 engines. The engine harnesses may have been manufactured without check engine light (CEL) and stop engine light (SEL) circuits, preventing the driver from being warned of a serious engine problem.
NHTSA 18V555000
Consequence: If the driver is not warned of a serious engine problem, the engine may unexpectedly fail, increasing the risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will inspect or test the ISX15 engine harness, and install an overlay jumper harness to supply the missing CEL and SEL circuits, free of charge. The recall began November 30, 2018. Owners may contact PACCAR customer service at 1-918-259-3258. PACCAR's number for this recall is 18KWE.
PACCAR Incorporated (PACCAR) is recalling certain 2016 Peterbilt 220, 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 389, 389G, 567, 579 and 587 trucks and Kenworth K170, T170, T270, T370, T440, T470,T660, T680, T800, T880, and W900 trucks equipped with certain Spicer D or E series steer axles. The castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen.
NHTSA 17V593000
Consequence: If the tie rod loosens, it may disconnect from the steering knuckle, causing a complete loss of steering and increasing the risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will inspect the torque of the castellated nut and tie rod, tightening it as necessary. If the tie rod stud and knuckle on units cannot be sufficiently torqued, the dealer will replace the knuckle and tie rod end assembly, free of charge. The recall began on November 13, 2017. Owners may contact Peterbilt customer service at 1-940-591-4000 or Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is P817-C.
PACCAR Incorporated (PACCAR) is recalling certain 2012-2018 Kenworth T800 and T880 vehicles equipped with Neway ADZ tridem rear suspensions. The brake control airline may be the incorrect size, resulting in an imbalance in the service brake application timing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air brake systems."
NHTSA 17V322000
Consequence: An incorrectly sized airline may lengthen the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy / Corrective Action
Kenworth will notify owners, and dealers will modify the air brake system with updated brake piping, free of charge. The recall began on June 21, 2017. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 17KWB.
PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T270, T370, T440, T470, C500, C540, C550, T660, T800, W900, and 963 trucks manufactured November 1, 2010, to April 6, 2015. In the affected trucks, water may leak into the wiper motor.
NHTSA 15V271000
Consequence: As water leaks in, the wiper may cease to function on the 'intermittent' setting, reducing the driver's visibility and increasing the risk of a crash. Additionally, the water may cause corrosion which, over time, may result in an electrical short, increasing the risk of a fire.
Remedy / Corrective Action
PACCAR is still developing and testing a remedy. The recall is expected to begin in July 2015. An interim letter was sent to owners on July 2, 2015. The recall began on September 2, 1015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWF.
PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.
NHTSA 15V309000
Consequence: If engine oil comes into contact with a hot surface, there is an increased risk of a fire.
Remedy / Corrective Action
Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.
PACCAR Incorporated (PACCAR) is recalling certain model year 2016 Kenworth T440, T470, T660, T680, T800, T880, and W900 trucks manufactured February 16, 2015, to March 9, 2015. The affected vehicles are equipped with an SR-7 spring brake valve assembly that may have had the primary and secondary service brake applications installed in reverse. In the event of a failure in the primary or secondary circuit, the redundant circuit would not provide adequate service brake functionality. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems."
NHTSA 15V457000
Consequence: A loss of braking ability would increase the risk of a crash.
Remedy / Corrective Action
Kenworth will notify owners, and dealers will inspect the vehicles and correct the air line installations as required, free of charge. The recall began on September 16, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWK.
Paccar Incorporated (Paccar) is recalling certain model year 2016 Kenworth T370, T660, T680, T800, T880, and W900 vehicles manufactured July 31, 2015, to August 12, 2015, and 2016 Peterbilt 337, 348, 365, 367, 382, 386, 389, 567, 579, and 587 vehicles manufactured August 4, 2015, to August 12, 2015. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.
NHTSA 15V597000
Consequence: An engine that stalls without warning increases the risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will replace the defective engine control modules, free of charge. The recall began on October 22, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. Paccar's numbers for this recall are 15KWM (Kenworth) and 915-L (Peterbilt).
PACCAR Incorporated (PACCAR) is recalling certain model year 2016 Kenworth T660, T680, T800, T880, and W900 trucks manufactured February 1, 2015, to April 20, 2015. During assembly, the affected vehicles did not undergo the rear wheel mounting torque verification process, and thus the rear wheels may be loose.
NHTSA 15V272000
Consequence: If the rear wheel lug nuts are undertorqued, the wheels may separate from the vehicle, increasing the risk of a crash.
Remedy / Corrective Action
Kenworth will notify owners, and dealers will verify that the rear wheel lug nuts are correctly tightened, free of charge. The recall began on July 1, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. Kenworth's number for this recall is 15KWG.
Paccar (Paccar Incorporated) is recalling certain 2016 Kenworth T680, T800, and T880 trucks manufactured January 5, 2015, to January 7, 2015 and 2016 Peterbilt 367, 384, 567, and 579 trucks manufactured January 2, 2015, to January 9, 2015 and equipped with Eaton Fuller FR 10-speed manual transmissions. In the affected vehicles, when the transmission shift lever is moved from reverse to neutral, the reverse gear may stay engaged. When the transmission shift lever is moved from reverse to a forward gear position, the transmission may mechanically lock because both the reverse gear and forward gear are simultaneously engaged.
NHTSA 15V639000
Consequence: Even though the transmission has been shifted out of reverse into neutral, the vehicle may unexpectedly move backwards, increasing the risk of a crash.
Remedy / Corrective Action
Paccar will notify the owners, and dealers will inspect and repair the affected transmissions if necessary, free of charge. The recall began on December 4, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. Paccar's numbers for this recall are 15KWM (Kenworth) and 1015N (Peterbilt).
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."
NHTSA 20V199000
Consequence: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.
Remedy / Corrective Action
PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."
NHTSA 24V145000
Consequence: Insufficient air volume can reduce braking performance and increase the risk of a crash.
Remedy / Corrective Action
Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.
Frequently Asked Questions
How many recalls does the 2016 KENWORTH T800 have?
The 2016 KENWORTH T800 currently has 12 recalls according to NHTSA records. All recall information is sourced directly from the National Highway Traffic Safety Administration database.
Are 2016 KENWORTH T800 recalls free to fix?
Yes! All safety recalls for 2016 KENWORTH T800 vehicles must be repaired free of charge by authorized dealers, regardless of vehicle age or mileage. Contact your local KENWORTH dealer to schedule a recall repair.
How do I check if my 2016 KENWORTH T800 has open recalls?
You can check for open recalls by entering your VIN (Vehicle Identification Number) in our VIN decoder tool. The 17-character VIN can be found on your vehicle registration, insurance card, or on the driver's side dashboard visible through the windshield.
Other Years - KENWORTH T800
2025 Recalls
2024 Recalls
2023 Recalls
2022 Recalls
2021 Recalls
2020 Recalls
2019 Recalls
2018 Recalls
2017 Recalls
2015 Recalls
2014 Recalls
2013 Recalls
2012 Recalls
2011 Recalls
2010 Recalls
Other KENWORTH Models
540
542
548CH
C5 Series
C500
C540
C550
K 100E
K100
K260/K360
K270/K370
K3 Series
K300
KS
KT
KW45/KW55
L7 Series
L700
L770
Other Off-Highway
Similar Brands
BUICK
27 models
TITAN
24 models
JAWA
1 models
OSHKOSH
64 models
DODGE
54 models
HYOSUNG
4 models
KYMCO
41 models
SHERCO
5 models
MERCEDES-BENZ
60 models
LINCOLN
17 models