Peterbilt 365 — MPG, VIN Decoder, Recalls, Reliability & Specs

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2021-2025 Peterbilt and Kenworth vehicles, equipped with Bendix EC80 Advanced Electronic Control Units (ECU). Please see the recall report for a complete list of models. Electrical noise and low signal to the power line carrier may cause the ECU to incorrectly process commands or stop functioning.

Risk. Safety systems that depend on the ECU (Automatic Traction Control, ABS, Electronic Stability Control, Active Cruise Control, and Collison Mitigation System) may not function properly or at all, increasing the risk of a crash.

Fix. Dealers will reprogram the ECU software, free of charge. Owner notification letters were mailed February 3, 2025. Owners may contact Kenworth's customer service at 1-425-828-5888 and Peterbilt's customer service at 1-940-591-4220. PACCAR's numbers for this recall are 24KWL and 24PBL.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2021-2024 Peterbilt 365, 367, 389, 535, 536, 537, 548, 567, 579, and 2021-2025 Kenworth T180, T280, T380, T480, T680, T880 and W990 trucks. The right-hand gear shifter stalk connectors may have been improperly crimped, resulting in a loss of communication.

Risk. A loss of communication between the gear shifter and the transmission may result in the vehicle becoming disabled after coming to a stop, increasing the risk of a crash.

Fix. Dealers will inspect and replace the gear shifter assembly as necessary, free of charge. Owner letters were mailed December 15, 2025, then phased after that. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 24PBE and 24KWE.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2021-2025 Peterbilt and Kenworth vehicles, equipped with Bendix EC80 Advanced Electronic Control Units (ECU). Please see the recall report for a complete list of models. Electrical noise and low signal to the power line carrier may cause the ECU to incorrectly process commands or stop functioning.

Risk. Safety systems that depend on the ECU (Automatic Traction Control, ABS, Electronic Stability Control, Active Cruise Control, and Collison Mitigation System) may not function properly or at all, increasing the risk of a crash.

Fix. Dealers will reprogram the ECU software, free of charge. Owner notification letters were mailed February 3, 2025. Owners may contact Kenworth's customer service at 1-425-828-5888 and Peterbilt's customer service at 1-940-591-4220. PACCAR's numbers for this recall are 24KWL and 24PBL.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2021-2024 Peterbilt 365, 367, 389, 535, 536, 537, 548, 567, 579, and 2021-2025 Kenworth T180, T280, T380, T480, T680, T880 and W990 trucks. The right-hand gear shifter stalk connectors may have been improperly crimped, resulting in a loss of communication.

Risk. A loss of communication between the gear shifter and the transmission may result in the vehicle becoming disabled after coming to a stop, increasing the risk of a crash.

Fix. Dealers will inspect and replace the gear shifter assembly as necessary, free of charge. Owner letters were mailed December 15, 2025, then phased after that. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 24PBE and 24KWE.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2022-2023 Kenworth T680, T880, W990, and Peterbilt 365, 367, 389, 567, and 579 vehicles. The digital display may freeze and not display critical safety information. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 101, "Control and Displays" and 102, "Trans Shift Lever Seq/Starter Interlock/Trans Braking Effect."

Risk. The loss of display information, such as vehicle speed and warning lights, can increase the risk of a crash.

Fix. Dealers will update the software, free of charge. Owner notification letters are expected to be mailed December 16, 2022. Owners may contact Kenworth's customer service at 1-425-828-5888 and Peterbilt's customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22KWK and 22PBK.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2022-2023 Kenworth T170, T270, T280, T370, T380, T440, T470, T480, T680, T800, T880, W900, W990, C500, and 2022-2023 Peterbilt 325, 330, 337, 348, 365, 367, 389, 520, 536, 537, 548, 567, and 579 vehicles. The steering gears may have been assembled incorrectly, which can cause the gears to fracture.

Risk. A fractured steering gear can cause a loss of steering control, increasing the risk of a crash.

Fix. Dealers will inspect the steering gear serial numbers, and replace the steering gears as necessary, free of charge. Owner notification letters were mailed September 26, 2022. Owners may contact Kenworth's customer service at 1-425-828-5888 and Peterbilt's customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22PBE and 22KWE.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2021-2025 Peterbilt and Kenworth vehicles, equipped with Bendix EC80 Advanced Electronic Control Units (ECU). Please see the recall report for a complete list of models. Electrical noise and low signal to the power line carrier may cause the ECU to incorrectly process commands or stop functioning.

Risk. Safety systems that depend on the ECU (Automatic Traction Control, ABS, Electronic Stability Control, Active Cruise Control, and Collison Mitigation System) may not function properly or at all, increasing the risk of a crash.

Fix. Dealers will reprogram the ECU software, free of charge. Owner notification letters were mailed February 3, 2025. Owners may contact Kenworth's customer service at 1-425-828-5888 and Peterbilt's customer service at 1-940-591-4220. PACCAR's numbers for this recall are 24KWL and 24PBL.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2021-2024 Peterbilt 365, 367, 389, 535, 536, 537, 548, 567, 579, and 2021-2025 Kenworth T180, T280, T380, T480, T680, T880 and W990 trucks. The right-hand gear shifter stalk connectors may have been improperly crimped, resulting in a loss of communication.

Risk. A loss of communication between the gear shifter and the transmission may result in the vehicle becoming disabled after coming to a stop, increasing the risk of a crash.

Fix. Dealers will inspect and replace the gear shifter assembly as necessary, free of charge. Owner letters were mailed December 15, 2025, then phased after that. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 24PBE and 24KWE.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2022-2023 Kenworth T680, T880, W990, and Peterbilt 365, 367, 389, 567, and 579 vehicles. The digital display may freeze and not display critical safety information. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 101, "Control and Displays" and 102, "Trans Shift Lever Seq/Starter Interlock/Trans Braking Effect."

Risk. The loss of display information, such as vehicle speed and warning lights, can increase the risk of a crash.

Fix. Dealers will update the software, free of charge. Owner notification letters are expected to be mailed December 16, 2022. Owners may contact Kenworth's customer service at 1-425-828-5888 and Peterbilt's customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22KWK and 22PBK.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2022-2023 Kenworth T170, T270, T280, T370, T380, T440, T470, T480, T680, T800, T880, W900, W990, C500, and 2022-2023 Peterbilt 325, 330, 337, 348, 365, 367, 389, 520, 536, 537, 548, 567, and 579 vehicles. The steering gears may have been assembled incorrectly, which can cause the gears to fracture.

Risk. A fractured steering gear can cause a loss of steering control, increasing the risk of a crash.

Fix. Dealers will inspect the steering gear serial numbers, and replace the steering gears as necessary, free of charge. Owner notification letters were mailed September 26, 2022. Owners may contact Kenworth's customer service at 1-425-828-5888 and Peterbilt's customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22PBE and 22KWE.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2021-2024 Peterbilt 365, 367, 389, 535, 536, 537, 548, 567, 579, and 2021-2025 Kenworth T180, T280, T380, T480, T680, T880 and W990 trucks. The right-hand gear shifter stalk connectors may have been improperly crimped, resulting in a loss of communication.

Risk. A loss of communication between the gear shifter and the transmission may result in the vehicle becoming disabled after coming to a stop, increasing the risk of a crash.

Fix. Dealers will inspect and replace the gear shifter assembly as necessary, free of charge. Owner letters were mailed December 15, 2025, then phased after that. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 24PBE and 24KWE.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2021 Peterbilt 337, 348, 365, 367, 520, 567, Kenworth T270, T370, T440, T470, T800 and T880 vehicles. The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Risk. A fuel leak in the presence of an ignition source increases the risk of a fire.

Fix. Dealers will inspect the rail threads and fuel lines, and replace the rail as necessary, free of charge. Owners may contact PACCAR customer service at 1-425-828-5888 (Kenworth) or 1-940-591-4220 (Peterbilt). PACCAR's numbers for this recall are 21KWC and 21PBD.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2020-2021 Peterbilt 348, 365, 367, 389, 520, 567 and Kenworth T800, T880, W900, W990 vehicles equipped with Watson and Chalin steerable lift axle suspension systems (model SL2065). The axles may have lower rear pivot bolts that are not long enough to sufficiently engage the locking feature of the corresponding nuts.

Risk. The short screws can cause the hardware to separate from the suspension system and become road hazards, increasing the risk of a crash and/or injury.

Fix. PACCAR will notify owners, and dealers will inspect suspect chassis and replace the pivot bolts, as necessary, free of charge. The recall began September 29, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall is 20PBE and 20KWC.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2020 Kenworth T270, T370, T440, T470, T660, T680, T880, T800, W900, W990; and 2018-2020 Peterbilt 330, 337, 348, 365, 367, 389, 520, 567, and 579 vehicles. The Dana D-Series axle steer arm fasteners that attach the steering arm to the steering knuckle may fail.

Risk. Fastener failure can result in a loss of steering control, increasing the risk of a crash or injury.

Fix. Dealers will replace and torque the steer arm fasteners, at no charge. Owner notification letters were mailed November 8, 2022. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22 PBB and 22 KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2021 Peterbilt 337, 348, 365, 367, 520, 567, Kenworth T270, T370, T440, T470, T800 and T880 vehicles. The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Risk. A fuel leak in the presence of an ignition source increases the risk of a fire.

Fix. Dealers will inspect the rail threads and fuel lines, and replace the rail as necessary, free of charge. Owners may contact PACCAR customer service at 1-425-828-5888 (Kenworth) or 1-940-591-4220 (Peterbilt). PACCAR's numbers for this recall are 21KWC and 21PBD.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.

Risk. An electrical short circuit can increase the risk of a fire.

Fix. PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2020-2021 Peterbilt 348, 365, 367, 389, 520, 567 and Kenworth T800, T880, W900, W990 vehicles equipped with Watson and Chalin steerable lift axle suspension systems (model SL2065). The axles may have lower rear pivot bolts that are not long enough to sufficiently engage the locking feature of the corresponding nuts.

Risk. The short screws can cause the hardware to separate from the suspension system and become road hazards, increasing the risk of a crash and/or injury.

Fix. PACCAR will notify owners, and dealers will inspect suspect chassis and replace the pivot bolts, as necessary, free of charge. The recall began September 29, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall is 20PBE and 20KWC.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2020 Kenworth T270, T370, T440, T470, T660, T680, T880, T800, W900, W990; and 2018-2020 Peterbilt 330, 337, 348, 365, 367, 389, 520, 567, and 579 vehicles. The Dana D-Series axle steer arm fasteners that attach the steering arm to the steering knuckle may fail.

Risk. Fastener failure can result in a loss of steering control, increasing the risk of a crash or injury.

Fix. Dealers will replace and torque the steer arm fasteners, at no charge. Owner notification letters were mailed November 8, 2022. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22 PBB and 22 KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2019 Peterbilt 337, 348, 365, 367, 389, 567, 579 and 587 trucks and 2018-2019 Kenworth C500, T270, T370, T440, T660, T680, T800, T880 and W900 trucks equipped with automated manual transmissions. An internal component in the clutch assembly may fail, possibly resulting in unintended vehicle movement.

Risk. Unintended movement of a vehicle can increase the risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the transmission control module, free of charge. The recall began February 23, 2019. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's numbers for this recall are 18PBE and 18KWH.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2021 Peterbilt 337, 348, 365, 367, 520, 567, Kenworth T270, T370, T440, T470, T800 and T880 vehicles. The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Risk. A fuel leak in the presence of an ignition source increases the risk of a fire.

Fix. Dealers will inspect the rail threads and fuel lines, and replace the rail as necessary, free of charge. Owners may contact PACCAR customer service at 1-425-828-5888 (Kenworth) or 1-940-591-4220 (Peterbilt). PACCAR's numbers for this recall are 21KWC and 21PBD.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.

Risk. An electrical short circuit can increase the risk of a fire.

Fix. PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2020 Kenworth T270, T370, T440, T470, T660, T680, T880, T800, W900, W990; and 2018-2020 Peterbilt 330, 337, 348, 365, 367, 389, 520, 567, and 579 vehicles. The Dana D-Series axle steer arm fasteners that attach the steering arm to the steering knuckle may fail.

Risk. Fastener failure can result in a loss of steering control, increasing the risk of a crash or injury.

Fix. Dealers will replace and torque the steer arm fasteners, at no charge. Owner notification letters were mailed November 8, 2022. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22 PBB and 22 KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2021 Peterbilt 337, 348, 365, 367, 520, 567, Kenworth T270, T370, T440, T470, T800 and T880 vehicles. The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Risk. A fuel leak in the presence of an ignition source increases the risk of a fire.

Fix. Dealers will inspect the rail threads and fuel lines, and replace the rail as necessary, free of charge. Owners may contact PACCAR customer service at 1-425-828-5888 (Kenworth) or 1-940-591-4220 (Peterbilt). PACCAR's numbers for this recall are 21KWC and 21PBD.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.

Risk. An electrical short circuit can increase the risk of a fire.

Fix. PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2018-2019 Peterbilt 337, 348, 365, 367, 389, 567, 579 and 587 trucks and 2018-2019 Kenworth C500, T270, T370, T440, T660, T680, T800, T880 and W900 trucks equipped with automated manual transmissions. An internal component in the clutch assembly may fail, possibly resulting in unintended vehicle movement.

Risk. Unintended movement of a vehicle can increase the risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the transmission control module, free of charge. The recall began February 23, 2019. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's numbers for this recall are 18PBE and 18KWH.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.

Risk. An electrical short circuit can increase the risk of a fire.

Fix. PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2017 Peterbilt 325, 330, 337, 348, 365, 367, 386, 389, and 587 vehicles manufactured April 20, 2016, to June 13, 2016. The brake lights may not illuminate when the brakes are applied. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk. If the brake lights do not illuminate when the brakes are applied, other drivers will be unaware the vehicle is stopping, which can increase the risk of a crash.

Fix. PACCAR will notify owners, and dealers will inspect and replace any brake light switches with date code 08-01760, free of charge. The recall began on January 26, 2017. Owners may contact Peterbilt customer service at 1-940-591-4000. Paccar's number for this recall is 816-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2017 Kenworth C500, T660, T680, T800, T880, and W900 vehicles manufactured March 9, 2016, to April 26, 2016 and 2017 Peterbilt 320, 365, 367, 389, 567, 579, and 587 vehicles manufactured March 10, 2016, to May 6, 2016. The affected vehicles are equipped with Cummins ISX12 or ISX15 engines and have an engine control module (ECM) that may short circuit, causing the engine to stall without warning without the ability to restart it.

Risk. An engine stall can increase the risk of a crash.

Fix. Cummins will notify owners, and Cummins dealers will replace the defective engine control modules, free of charge. The began on July 8, 2016. Owners may contact Cummins customer service at 1-800-343-7357, Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall are 16KWB (Kenworth) and 616-C (Peterbilt).

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.

Risk. An electrical short circuit can increase the risk of a fire.

Fix. PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2015-2016 Peterbilt 365 and 367 vehicles manufactured from August 27, 2014, through June 5, 2015, and equipped with drive axles manufactured by Marmon-Herrington. The affected axles have hex nuts on the flange yoke that may not have been properly tightened.

Risk. If the hex nuts are not tightened to specification, the driveshaft may disconnect from the drive axle, resulting in a loss of propulsion and increasing the risk of a crash.

Fix. Peterbilt will notify the owners, and dealers will inspect the torque and, if necessary, tighten the bolts, free of charge. The recall began on March 11, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall campaign is 216-A.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2010 Peterbilt 340, 2010, 2012, and 2015-2016 Peterbilt 337, 2010 Peterbilt 335, 2011-2016 Peterbilt 348, 2009 and 2011-2016 Peterbilt 365, 2009 and 2012-2013 Peterbilt 386, 2009-2015 Peterbilt 388, 2015-2016 Peterbilt 389, and 2015 Peterbilt 567 auto hauler vehicles. The affected trucks are equipped with Michelin 295/60R22.5 XZA-2 front tires that have a speed rating less than the vehicle is governed to.

Risk. Higher vehicle speeds and other factors such as tire load and road temperatures may result in premature tire failure, increasing the risk of a crash.

Fix. Peterbilt will notify owners, and dealers will reprogram the engine's vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating, free of charge. The recall began on January 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1115P.

What's wrong. Paccar Incorporated (Paccar) is recalling certain model year 2016 Kenworth T370, T660, T680, T800, T880, and W900 vehicles manufactured July 31, 2015, to August 12, 2015, and 2016 Peterbilt 337, 348, 365, 367, 382, 386, 389, 567, 579, and 587 vehicles manufactured August 4, 2015, to August 12, 2015. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.

Risk. An engine that stalls without warning increases the risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the defective engine control modules, free of charge. The recall began on October 22, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. Paccar's numbers for this recall are 15KWM (Kenworth) and 915-L (Peterbilt).

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2012-2016 Peterbilt 365, 367, 384, 386, 388, 389, 567, 579, and 587 trucks manufactured January 13, 2011, to April 20, 2015. The affected trucks, equipped with extended-body Leece Neville alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

Risk. If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

Fix. Peterbilt will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line and install a plastic insulator on the cable end, free of charge. The recall began on September 23, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. Peterbilt's number for this recall is 715-K.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2016 Peterbilt 220, 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 389, 389G, 567, 579 and 587 trucks and Kenworth K170, T170, T270, T370, T440, T470,T660, T680, T800, T880, and W900 trucks equipped with certain Spicer D or E series steer axles. The castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen.

Risk. If the tie rod loosens, it may disconnect from the steering knuckle, causing a complete loss of steering and increasing the risk of a crash.

Fix. PACCAR will notify owners, and dealers will inspect the torque of the castellated nut and tie rod, tightening it as necessary. If the tie rod stud and knuckle on units cannot be sufficiently torqued, the dealer will replace the knuckle and tie rod end assembly, free of charge. The recall began on November 13, 2017. Owners may contact Peterbilt customer service at 1-940-591-4000 or Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is P817-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.

Risk. An electrical short circuit can increase the risk of a fire.

Fix. PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2010 Peterbilt 340, 2010, 2012, and 2015-2016 Peterbilt 337, 2010 Peterbilt 335, 2011-2016 Peterbilt 348, 2009 and 2011-2016 Peterbilt 365, 2009 and 2012-2013 Peterbilt 386, 2009-2015 Peterbilt 388, 2015-2016 Peterbilt 389, and 2015 Peterbilt 567 auto hauler vehicles. The affected trucks are equipped with Michelin 295/60R22.5 XZA-2 front tires that have a speed rating less than the vehicle is governed to.

Risk. Higher vehicle speeds and other factors such as tire load and road temperatures may result in premature tire failure, increasing the risk of a crash.

Fix. Peterbilt will notify owners, and dealers will reprogram the engine's vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating, free of charge. The recall began on January 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1115P.

What's wrong. PACCAR Inc, is recalling certain model year 2014-2015 Kenworth T440, T660, T800, and W900 tractor trailers manufactured January 23, 2013, through February 4, 2014, and certain model year 2014-2015 Peterbilt 320, 365, 382, 384 tractor trailers manufactured January 21, 2013, through February 5, 2014, and equipped with certain Cummins Westport Model ISL G and ISX12 G engines. Condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor.

Risk. The improper operation of the sensor could induce elevated exhaust temperatures or flames from the exhaust pipe, increasing the risk of a vehicle fire or burn injury to a person near the exhaust pipe.

Fix. PACCAR will notify owners, and authorized Cummins service facilities will upload a new ECM calibration, free of charge. The recall began on April 12, 2014. Customers may contact PACCAR at 1-425-468-7400. Paccar's recall numbers associated with this campaign are 14KWG (Kenworth), and 214-C (Peterbilt).

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2012-2016 Peterbilt 365, 367, 384, 386, 388, 389, 567, 579, and 587 trucks manufactured January 13, 2011, to April 20, 2015. The affected trucks, equipped with extended-body Leece Neville alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

Risk. If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

Fix. Peterbilt will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line and install a plastic insulator on the cable end, free of charge. The recall began on September 23, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. Peterbilt's number for this recall is 715-K.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2015 Peterbilt 579, 388, 384, 367, 365, 348, and 337 trucks manufactured October 30, 2009, through May 21, 2014. In the affected vehicles, if power is interrupted to the seat electronic control unit (ECU), such as when the fuse for that circuit blows, the side air bag would be disabled but there will not be a warning lamp indicator to notify the operator of the malfunction.

Risk. Without a warning of a problem existing in the side air bag system, the driver may continue to operate the vehicle, increasing the risk of injury from the side air bag not deploying in the event of a rollover.

Fix. PACCAR will notify owners, and dealers will install a new electrical harness to correct them problem, free of charge. The recall began in July 2014. Owners may contact Peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 514-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.

Risk. Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2015-2016 Peterbilt 365 and 367 vehicles manufactured from August 27, 2014, through June 5, 2015, and equipped with drive axles manufactured by Marmon-Herrington. The affected axles have hex nuts on the flange yoke that may not have been properly tightened.

Risk. If the hex nuts are not tightened to specification, the driveshaft may disconnect from the drive axle, resulting in a loss of propulsion and increasing the risk of a crash.

Fix. Peterbilt will notify the owners, and dealers will inspect the torque and, if necessary, tighten the bolts, free of charge. The recall began on March 11, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall campaign is 216-A.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2015 Kenworth K270, T270, K370, T370, T440, T470, and W900 chassis manufactured May 13, 2014, to July 23, 2014, and certain model year 2015 Peterbilt 210, 220, 320, 325, 330, 337, 348, 365, 382, 384, and 567 chassis manufactured May 8, 2014, to July 22, 2014. The Cummins ISB or ISL engines in these vehicles may have been equipped with Fleetguard UFF-XT fuel filters, part number FF63009, whose filter shell may separate from the fuel filter nut plate causing the engine to stall without warning.

Risk. If the engine stalls unexpectedly there is an increased risk of a crash.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins dealers will replace the fuel filter with a non-defective one, free of charge. The notification schedule for this recall ran July 29 to December 31, 2014. Owners may contact Kenworth customer service at 1-425-828-5000, or Peterbilt customer service at 1-940-591-4000. Owners may also contact Cummins customer service at 1-812-377-3713. Kenworth's number for this recall is 14KWJ. Peterbilt's number for this recall is 814-H.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk. If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2014 Kenworth T660, T680, T700,T800, T880, W900, T440, T470, T370, T270, T170, C500, and C550 chassis manufactured between August 7, 2013, and October 31, 2013, and Peterbilt 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 chassis manufactured between August 7, 2013, and November 3, 2013, and equipped with IMMI-brand L9 seat belt buckles. When the button is pressed to release the seat belt, the latch plate can become partially engaged with the buckle, making the seat belt difficult to unlatch. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 209, "Seat Belt Assemblies."

Risk. If the latch plate remains partially engaged after the button is pressed, egress from the vehicle could be hindered which would increase the risk of injury in the event of an emergency.

Fix. PACCAR will notify owners, and dealers will inspect and replace the seat belt buckles, as necessary, free of charge. The recall began on March 31, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's number for this campaign is 14KWC. Peterbilt's number for this campaign is 114-B.

What's wrong. PACCAR is recalling certain model year 2014 Kenworth T170, T270, T370, T470, T660, T680, T800, T880, and W900 trucks manufactured May 6, 2013, through May 17, 2013; and model year 2014 Peterbilt 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, 389K, 567, 579 and 587 trucks manufactured May 1, 2013 through May 17, 2013. An internal defect in the ignition switch causes the starter to engage when a key is partially inserted, before the key is turned.

Risk. Unintended engine startup could cause injury to a person working in the engine compartment. Vehicles with standard transmissions may experience unexpected movement, which may result in personal injury or a crash.

Fix. PACCAR will notify owners, and dealers will replace affected ignition switches, free of charge. The recall began on June 14, 2013. Owners may contact Kenworth at 1-425-828-5000 or Peterbilt at 1-940-591-4000. Kenworth's recall campaign number is 13KWF. Peterbilt's recall campaign number is 0513-E.

What's wrong. PACCAR Inc, is recalling certain model year 2014-2015 Kenworth T440, T660, T800, and W900 tractor trailers manufactured January 23, 2013, through February 4, 2014, and certain model year 2014-2015 Peterbilt 320, 365, 382, 384 tractor trailers manufactured January 21, 2013, through February 5, 2014, and equipped with certain Cummins Westport Model ISL G and ISX12 G engines. Condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor.

Risk. The improper operation of the sensor could induce elevated exhaust temperatures or flames from the exhaust pipe, increasing the risk of a vehicle fire or burn injury to a person near the exhaust pipe.

Fix. PACCAR will notify owners, and authorized Cummins service facilities will upload a new ECM calibration, free of charge. The recall began on April 12, 2014. Customers may contact PACCAR at 1-425-468-7400. Paccar's recall numbers associated with this campaign are 14KWG (Kenworth), and 214-C (Peterbilt).

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk. If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2012-2016 Peterbilt 365, 367, 384, 386, 388, 389, 567, 579, and 587 trucks manufactured January 13, 2011, to April 20, 2015. The affected trucks, equipped with extended-body Leece Neville alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

Risk. If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

Fix. Peterbilt will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line and install a plastic insulator on the cable end, free of charge. The recall began on September 23, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. Peterbilt's number for this recall is 715-K.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2015 Peterbilt 579, 388, 384, 367, 365, 348, and 337 trucks manufactured October 30, 2009, through May 21, 2014. In the affected vehicles, if power is interrupted to the seat electronic control unit (ECU), such as when the fuse for that circuit blows, the side air bag would be disabled but there will not be a warning lamp indicator to notify the operator of the malfunction.

Risk. Without a warning of a problem existing in the side air bag system, the driver may continue to operate the vehicle, increasing the risk of injury from the side air bag not deploying in the event of a rollover.

Fix. PACCAR will notify owners, and dealers will install a new electrical harness to correct them problem, free of charge. The recall began in July 2014. Owners may contact Peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 514-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.

Risk. Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2010 Peterbilt 340, 2010, 2012, and 2015-2016 Peterbilt 337, 2010 Peterbilt 335, 2011-2016 Peterbilt 348, 2009 and 2011-2016 Peterbilt 365, 2009 and 2012-2013 Peterbilt 386, 2009-2015 Peterbilt 388, 2015-2016 Peterbilt 389, and 2015 Peterbilt 567 auto hauler vehicles. The affected trucks are equipped with Michelin 295/60R22.5 XZA-2 front tires that have a speed rating less than the vehicle is governed to.

Risk. Higher vehicle speeds and other factors such as tire load and road temperatures may result in premature tire failure, increasing the risk of a crash.

Fix. Peterbilt will notify owners, and dealers will reprogram the engine's vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating, free of charge. The recall began on January 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1115P.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar is recalling certain model year 2012-2013 kenworth t170, t270, t370, t440, t470, t660, t700, t800, w900, and peterbilt 320, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 vehicles, manufactured from january 31, 2011, through january 19, 2012, and equipped with bendix atr-6 antilock traction relay valves. In extremely cold conditions, these bendix relay valves may potentially develop internal leakage. Internal leakage can lead to air pressure being delivered to affected primary or secondary brake causing continuous brake application.

Risk. Unexpected continuous brake application can cause the brakes to overheat and lead to a fire. Unexpected continuous brake application can cause the driver to lose control of the vehicle, increasing the risk of a crash. Also, the brakes may be applied without illuminating the brake lights, failing to give proper warning to other drivers.

Fix. Paccar will notify owners, and provide a temporary repair until bendix develops a permanent remedy. This service will be performed free of charge. The safety recall began on february 10, 2012. Owner may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings installed on front axles rated to carry between 20,001 and 22,000 lbs GAWR and larger SLR (20.5" to 21.5") tires, however these brake linings are not rated for this configuration. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."

Risk. The improper brake configuration could lengthen the braking distance needed to stop the vehicle, increasing the risk of a crash.

Fix. PACCAR will notify owners and dealers will install new 16.5" x 7" brake shoes with ES-600 linings, free of charge. The recall began on June 20, 2014. Owners may contact at Peterbilt at 1-800-473-8372. Peterbilt's number for this recall is 314-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2012-2016 Peterbilt 365, 367, 384, 386, 388, 389, 567, 579, and 587 trucks manufactured January 13, 2011, to April 20, 2015. The affected trucks, equipped with extended-body Leece Neville alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

Risk. If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

Fix. Peterbilt will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line and install a plastic insulator on the cable end, free of charge. The recall began on September 23, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. Peterbilt's number for this recall is 715-K.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2015 Peterbilt 579, 388, 384, 367, 365, 348, and 337 trucks manufactured October 30, 2009, through May 21, 2014. In the affected vehicles, if power is interrupted to the seat electronic control unit (ECU), such as when the fuse for that circuit blows, the side air bag would be disabled but there will not be a warning lamp indicator to notify the operator of the malfunction.

Risk. Without a warning of a problem existing in the side air bag system, the driver may continue to operate the vehicle, increasing the risk of injury from the side air bag not deploying in the event of a rollover.

Fix. PACCAR will notify owners, and dealers will install a new electrical harness to correct them problem, free of charge. The recall began in July 2014. Owners may contact Peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 514-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.

Risk. Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk. If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2010 Peterbilt 340, 2010, 2012, and 2015-2016 Peterbilt 337, 2010 Peterbilt 335, 2011-2016 Peterbilt 348, 2009 and 2011-2016 Peterbilt 365, 2009 and 2012-2013 Peterbilt 386, 2009-2015 Peterbilt 388, 2015-2016 Peterbilt 389, and 2015 Peterbilt 567 auto hauler vehicles. The affected trucks are equipped with Michelin 295/60R22.5 XZA-2 front tires that have a speed rating less than the vehicle is governed to.

Risk. Higher vehicle speeds and other factors such as tire load and road temperatures may result in premature tire failure, increasing the risk of a crash.

Fix. Peterbilt will notify owners, and dealers will reprogram the engine's vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating, free of charge. The recall began on January 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1115P.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar is recalling certain model year 2012-2013 kenworth t170, t270, t370, t440, t470, t660, t700, t800, w900, and peterbilt 320, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 vehicles, manufactured from january 31, 2011, through january 19, 2012, and equipped with bendix atr-6 antilock traction relay valves. In extremely cold conditions, these bendix relay valves may potentially develop internal leakage. Internal leakage can lead to air pressure being delivered to affected primary or secondary brake causing continuous brake application.

Risk. Unexpected continuous brake application can cause the brakes to overheat and lead to a fire. Unexpected continuous brake application can cause the driver to lose control of the vehicle, increasing the risk of a crash. Also, the brakes may be applied without illuminating the brake lights, failing to give proper warning to other drivers.

Fix. Paccar will notify owners, and provide a temporary repair until bendix develops a permanent remedy. This service will be performed free of charge. The safety recall began on february 10, 2012. Owner may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2010 Peterbilt 340, 2010, 2012, and 2015-2016 Peterbilt 337, 2010 Peterbilt 335, 2011-2016 Peterbilt 348, 2009 and 2011-2016 Peterbilt 365, 2009 and 2012-2013 Peterbilt 386, 2009-2015 Peterbilt 388, 2015-2016 Peterbilt 389, and 2015 Peterbilt 567 auto hauler vehicles. The affected trucks are equipped with Michelin 295/60R22.5 XZA-2 front tires that have a speed rating less than the vehicle is governed to.

Risk. Higher vehicle speeds and other factors such as tire load and road temperatures may result in premature tire failure, increasing the risk of a crash.

Fix. Peterbilt will notify owners, and dealers will reprogram the engine's vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating, free of charge. The recall began on January 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1115P.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2012-2016 Peterbilt 365, 367, 384, 386, 388, 389, 567, 579, and 587 trucks manufactured January 13, 2011, to April 20, 2015. The affected trucks, equipped with extended-body Leece Neville alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

Risk. If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

Fix. Peterbilt will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line and install a plastic insulator on the cable end, free of charge. The recall began on September 23, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. Peterbilt's number for this recall is 715-K.

What's wrong. PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings installed on front axles rated to carry between 20,001 and 22,000 lbs GAWR and larger SLR (20.5" to 21.5") tires, however these brake linings are not rated for this configuration. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."

Risk. The improper brake configuration could lengthen the braking distance needed to stop the vehicle, increasing the risk of a crash.

Fix. PACCAR will notify owners and dealers will install new 16.5" x 7" brake shoes with ES-600 linings, free of charge. The recall began on June 20, 2014. Owners may contact at Peterbilt at 1-800-473-8372. Peterbilt's number for this recall is 314-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk. If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2015 Peterbilt 579, 388, 384, 367, 365, 348, and 337 trucks manufactured October 30, 2009, through May 21, 2014. In the affected vehicles, if power is interrupted to the seat electronic control unit (ECU), such as when the fuse for that circuit blows, the side air bag would be disabled but there will not be a warning lamp indicator to notify the operator of the malfunction.

Risk. Without a warning of a problem existing in the side air bag system, the driver may continue to operate the vehicle, increasing the risk of injury from the side air bag not deploying in the event of a rollover.

Fix. PACCAR will notify owners, and dealers will install a new electrical harness to correct them problem, free of charge. The recall began in July 2014. Owners may contact Peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 514-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.

Risk. Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. Paccar is recalling certain model year kenworth and peterbilt vehicles. A manufacturing defect in the seal supplied by a component manufacturer installed on the output shaft of the exhaust gas recirculation (egr) valve actuator may cause eventual delamination of the seal. Delamination of the seal may allow engine oil to leak from the egr valve onto exhaust components.

Risk. The leaking of engine oil onto hot exhaust components, such as when the engine is under significant load, may create the possibility of a fire.

Fix. Dealers will replace the egr valve assembly on the subject vehicles equipped with the paccar mx engine. This service will be performed free of charge. The safety recall began on october 29, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar is recalling certain model year 2011-2012 kenworth t660, t700, and t800 vehicles manufactured from april 19, 2010, through may 13, 2011, and model year 2008, 2010, and 2011 peterbilt 365, 367, 384, 386, 387, 388 and 587 vehicles manufactured from april 20, 2010, through june 11, 2011, and equipped with paccar mx engines and eaton ultrashift dm or allison automatic transmissions (without auto-neutral). The fast idle control may be activated by the operator while the transmission is in gear.

Risk. If the fast idle control function is engaged with the transmission in gear, the vehicle could unexpectedly accelerate and override the parking brake and , creating a risk of a crash and damage to other vehicles or property and the potential for injury to nearby pedestrians.

Fix. Kenworth and peterbilt dealers will update the engine software for the affected chassis. This service will be performed free of charge. The safety recall began on august 22, 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Risk. The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.

Fix. Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings installed on front axles rated to carry between 20,001 and 22,000 lbs GAWR and larger SLR (20.5" to 21.5") tires, however these brake linings are not rated for this configuration. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."

Risk. The improper brake configuration could lengthen the braking distance needed to stop the vehicle, increasing the risk of a crash.

Fix. PACCAR will notify owners and dealers will install new 16.5" x 7" brake shoes with ES-600 linings, free of charge. The recall began on June 20, 2014. Owners may contact at Peterbilt at 1-800-473-8372. Peterbilt's number for this recall is 314-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk. If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2015 Peterbilt 579, 388, 384, 367, 365, 348, and 337 trucks manufactured October 30, 2009, through May 21, 2014. In the affected vehicles, if power is interrupted to the seat electronic control unit (ECU), such as when the fuse for that circuit blows, the side air bag would be disabled but there will not be a warning lamp indicator to notify the operator of the malfunction.

Risk. Without a warning of a problem existing in the side air bag system, the driver may continue to operate the vehicle, increasing the risk of injury from the side air bag not deploying in the event of a rollover.

Fix. PACCAR will notify owners, and dealers will install a new electrical harness to correct them problem, free of charge. The recall began in July 2014. Owners may contact Peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 514-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.

Risk. Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2010 Peterbilt 340, 2010, 2012, and 2015-2016 Peterbilt 337, 2010 Peterbilt 335, 2011-2016 Peterbilt 348, 2009 and 2011-2016 Peterbilt 365, 2009 and 2012-2013 Peterbilt 386, 2009-2015 Peterbilt 388, 2015-2016 Peterbilt 389, and 2015 Peterbilt 567 auto hauler vehicles. The affected trucks are equipped with Michelin 295/60R22.5 XZA-2 front tires that have a speed rating less than the vehicle is governed to.

Risk. Higher vehicle speeds and other factors such as tire load and road temperatures may result in premature tire failure, increasing the risk of a crash.

Fix. Peterbilt will notify owners, and dealers will reprogram the engine's vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating, free of charge. The recall began on January 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1115P.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Risk. A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.

Fix. Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar is recalling certain model year 2011-2012 kenworth t660, t700, and t800 vehicles manufactured from april 19, 2010, through may 13, 2011, and model year 2008, 2010, and 2011 peterbilt 365, 367, 384, 386, 387, 388 and 587 vehicles manufactured from april 20, 2010, through june 11, 2011, and equipped with paccar mx engines and eaton ultrashift dm or allison automatic transmissions (without auto-neutral). The fast idle control may be activated by the operator while the transmission is in gear.

Risk. If the fast idle control function is engaged with the transmission in gear, the vehicle could unexpectedly accelerate and override the parking brake and , creating a risk of a crash and damage to other vehicles or property and the potential for injury to nearby pedestrians.

Fix. Kenworth and peterbilt dealers will update the engine software for the affected chassis. This service will be performed free of charge. The safety recall began on august 22, 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Risk. The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.

Fix. Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk. If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

What's wrong. PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings installed on front axles rated to carry between 20,001 and 22,000 lbs GAWR and larger SLR (20.5" to 21.5") tires, however these brake linings are not rated for this configuration. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."

Risk. The improper brake configuration could lengthen the braking distance needed to stop the vehicle, increasing the risk of a crash.

Fix. PACCAR will notify owners and dealers will install new 16.5" x 7" brake shoes with ES-600 linings, free of charge. The recall began on June 20, 2014. Owners may contact at Peterbilt at 1-800-473-8372. Peterbilt's number for this recall is 314-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2015 Peterbilt 579, 388, 384, 367, 365, 348, and 337 trucks manufactured October 30, 2009, through May 21, 2014. In the affected vehicles, if power is interrupted to the seat electronic control unit (ECU), such as when the fuse for that circuit blows, the side air bag would be disabled but there will not be a warning lamp indicator to notify the operator of the malfunction.

Risk. Without a warning of a problem existing in the side air bag system, the driver may continue to operate the vehicle, increasing the risk of injury from the side air bag not deploying in the event of a rollover.

Fix. PACCAR will notify owners, and dealers will install a new electrical harness to correct them problem, free of charge. The recall began in July 2014. Owners may contact Peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 514-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.

Risk. Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

What's wrong. Paccar is recalling 1,043 my 2008-2009 kenworth c500, t2000,t660, t800 and w900 trucks equipped with bendix mv-3 dash control valves. The molded valve body has an incorrect core pin in the injection mold causing the valve body to be oversized in the double check valve area. This condition can allow the rubber double check valve to become lodged in the body opening under certain circumstances.

Risk. If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged double check valve thereby depleting the secondary reservoir, causing reduced ability for modulating the service emergency brakes. In such an event, the operator should observe an air leak, indications of low air pressure via the primary and secondary air gauges, and audible and visual low air pressure warning alarms. A vehicle crash is possible if these warnings are not heeded.

Fix. Dealers will replace the bendix mv-3 dash control valves free of charge. The recall began on april 14, 2008. Owners may contact kenworth at 1-425-828-4196.

What's wrong. Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Risk. A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.

Fix. Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

What's wrong. Paccar is recalling 2,096 my 2009 kenworth and peterbilt vehicles equipped with trw steering shafts. Mislocation of a circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Risk. A separation of the splined and non-splined tubes could cause a loss of steering control and increase the risk of a crash.

Fix. Dealers will inspect the steering shaft using a weld placement gauge and miswelded steering shaft will be replaced free of charge. The recall began july 31, 2009. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling 86 my 2009 kenworth t660, t800, w900, and peterbilt 386, 365, and 388 trucks equipped with bendix front air disc brakes. The size 14 service chamber of certain front air disc brakes may have been contaminated with grease between the piston head/plate and the diaphragm. When braking pressure is applied, the grease may allow the piston head/plate to slip off center and catch on the reducing ring of the size 14 service chamber.

Risk. The catching of the piston head/plate on the reducing ring may lock up the corresponding front air disc brake which may impact the operator's ability to steer or control the vehicle.

Fix. Dealers will replace both front air disc brakes size 14 service chambers free of charge. The recall began on august 27, 2008. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar is recalling 4,883 my 2006-2009 kenworth t600, t660, t800, w900, t2000 and my 2008-2009 peterbilt 365, 367, 379, 384, 386, 387, 388 and 389 trucks. Inadequate stiffness of the diesel particulate filter (dpf) bracket could result in separation of the dpf from the chassis.

Risk. A vehicle crash could occur if another vehicle strikes the dpf on the roadway.

Fix. Paccar is working with caterpillar to repair these vehicles (please see 08e041). Owners may contact caterpillar at 1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling 263 my 2008-2009 kenworth t800, w900 and peterbilt 365 and 384 trucks equipped with c7 or c9 caterpillar diesel engines. The fuel pump outlet check plug may be cracked which could cause fuel to spray and leak.

Risk. Fuel leakage, in the presence of an ignition source, could result in a fire.

Fix. Paccar is working with caterpillar (please see 08e042). Caterpillar will replace the fuel pump plug free of charge. The recall is expected to begin during september 2008. Owners may contact caterpillar at-1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Risk. The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.

Fix. Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings installed on front axles rated to carry between 20,001 and 22,000 lbs GAWR and larger SLR (20.5" to 21.5") tires, however these brake linings are not rated for this configuration. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."

Risk. The improper brake configuration could lengthen the braking distance needed to stop the vehicle, increasing the risk of a crash.

Fix. PACCAR will notify owners and dealers will install new 16.5" x 7" brake shoes with ES-600 linings, free of charge. The recall began on June 20, 2014. Owners may contact at Peterbilt at 1-800-473-8372. Peterbilt's number for this recall is 314-D.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2010 Peterbilt 340, 2010, 2012, and 2015-2016 Peterbilt 337, 2010 Peterbilt 335, 2011-2016 Peterbilt 348, 2009 and 2011-2016 Peterbilt 365, 2009 and 2012-2013 Peterbilt 386, 2009-2015 Peterbilt 388, 2015-2016 Peterbilt 389, and 2015 Peterbilt 567 auto hauler vehicles. The affected trucks are equipped with Michelin 295/60R22.5 XZA-2 front tires that have a speed rating less than the vehicle is governed to.

Risk. Higher vehicle speeds and other factors such as tire load and road temperatures may result in premature tire failure, increasing the risk of a crash.

Fix. Peterbilt will notify owners, and dealers will reprogram the engine's vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating, free of charge. The recall began on January 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1115P.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.

Risk. Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.

Fix. PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk. If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Fix. Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

What's wrong. On certain kenworth and peterbilt heavy duty trucks equipped with tas-85 trw steering gears, the inner surface of the outer sector shaft teeth of the steering gears may have an incorrect involute profile, which may lead to chipping and damage of the gearing system.

Risk. This type of damage may cause a "bind/stick" condition in the vehicle steering during a turn increasing the risk of a crash.

Fix. Dealers will repair and replace any suspect tas-85 steering gear assembly free of charge. The recall began on january 9, 2008. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4201.

What's wrong. On certain trucks built with cummins ism c876 engines, the electronic control module fails to recognize inputs of the vehicle electronic control unit or from a driver actuated dash switch thereby increasing the risk of unintended (or unexpected) elevated exhaust temperatures.

Risk. While this condition does not involve a risk of fire in the vehicle itself, it could present a fire hazard in a situation where the vehicle's exhaust is in close proximity to materials or substances that can melt, burn, or explode.

Fix. Cummins, in conjunction with paccar, will conduct the remedy campaign. Cummis will install new ecm software. Owners can contact cummins at 1-800-343-7357, peterbilt at 940-591-4201 or kenworth at 425-828-5440.

What's wrong. Paccar is recalling 318 my 2007-2009 kenworth t800, w900, and peterbilt 357, 365, 367, 378, 379, 384, 385, 386,388, and 389 trucks equipped with premier trailer hitch assemblies. The pintle hitch assemblies may have been manufactured in a manner resulting in a reduction of fatigue strength of the pivot pins.

Risk. This reduction of fatigue strength could cause the pivot pin to crack and eventually break, causing the trailer to detach from the truck while in motion, which could cause a crash that could result in personal injury or death.

Fix. Dealers will replace the potentially defective pivot pin free of charge. The recall began on april 18, 2008. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. Certain trucks equipped with eaton synflex eclipse brand extruded nylon air brake hose tubing fail to comply with the requirements of federal motor vehicle safety standard no. 106, "brake hoses." the tubing was manufactured with only four layers of nylon material, instead of the specified five layers.

Risk. The diameter of the hose affects the fittings which may allow air to leak from the brakes and create the potential for a vehicle crash.

Fix. Dealers will inspect the air brake hoses and, if necessary, replace the hoses. The recall began on february 22, 2008. Owner notification schedule for this campaign. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Risk. A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.

Fix. Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

What's wrong. Paccar is recalling 6,169 my 2008 kenworth t300, t660, t800, t2000, w900 and c500 vehicles and my 2008-2009 peterbilt models 365, 367, 384, 387, 388, 389 and 389 kits. Certain door latch assemblies on these vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 206, 'door locks and door retention components." the rotor in some of these door latch assemblies did not receive the proper heat treatment and may be soft.

Risk. In the event of a crash, force could cause the rotor to crack and the door would not have primary or secondary closing security which could possibly lead to injury of the vehicle occupant.

Fix. Paccar is working with trimark and will inspect and replace the door latch if it is found to be defective. The recall began on march 14, 2008. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar is recalling certain model year 2011-2012 kenworth t660, t700, and t800 vehicles manufactured from april 19, 2010, through may 13, 2011, and model year 2008, 2010, and 2011 peterbilt 365, 367, 384, 386, 387, 388 and 587 vehicles manufactured from april 20, 2010, through june 11, 2011, and equipped with paccar mx engines and eaton ultrashift dm or allison automatic transmissions (without auto-neutral). The fast idle control may be activated by the operator while the transmission is in gear.

Risk. If the fast idle control function is engaged with the transmission in gear, the vehicle could unexpectedly accelerate and override the parking brake and , creating a risk of a crash and damage to other vehicles or property and the potential for injury to nearby pedestrians.

Fix. Kenworth and peterbilt dealers will update the engine software for the affected chassis. This service will be performed free of charge. The safety recall began on august 22, 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Risk. The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.

Fix. Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling 4,883 my 2006-2009 kenworth t600, t660, t800, w900, t2000 and my 2008-2009 peterbilt 365, 367, 379, 384, 386, 387, 388 and 389 trucks. Inadequate stiffness of the diesel particulate filter (dpf) bracket could result in separation of the dpf from the chassis.

Risk. A vehicle crash could occur if another vehicle strikes the dpf on the roadway.

Fix. Paccar is working with caterpillar to repair these vehicles (please see 08e041). Owners may contact caterpillar at 1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling 263 my 2008-2009 kenworth t800, w900 and peterbilt 365 and 384 trucks equipped with c7 or c9 caterpillar diesel engines. The fuel pump outlet check plug may be cracked which could cause fuel to spray and leak.

Risk. Fuel leakage, in the presence of an ignition source, could result in a fire.

Fix. Paccar is working with caterpillar (please see 08e042). Caterpillar will replace the fuel pump plug free of charge. The recall is expected to begin during september 2008. Owners may contact caterpillar at-1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. On some peterbilt trucks, certain parts used in the air suspensions have a high copper content causing premature failure.

Risk. Failure could cause erratic vehicle handling which can cause a vehicle crash without warning.

Fix. Dealers will inspect and, when necessary, replace the defective parts. The recall began on january 17, 2007. Owners may contact peterbilt at 1-940-591-4196.

What's wrong. On certain trucks, if the ignition switch is turned on prior to initial start up in the manufacturing plant or during the filter replacement in the field, a small flame will ignite when the fuel is added to prime the system.

Risk. The possibility exists for the flame to spread resulting in possible equipment damage or physical injury.

Fix. Dealers will inspect the filter for the date codes of the suspect filters and replace those heating elements free of charge. The recall began on march 21, 2007. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4201.

What's wrong. On certain trucks, the axle housings may have been manufactured with steel that was out of specification which could result in a fatigue failure over time.

Risk. If a fatigue failure occurs and is left unattended, the axle may lock up or the end of the axle could come off, which may result in a vehicle crash.

Fix. Dealers will inspect and replace the axles free of charge. The recall began on may 9, 2007. Owners may contact kenworth at 425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. Paccar is recalling 318 my 2007-2009 kenworth t800, w900, and peterbilt 357, 365, 367, 378, 379, 384, 385, 386,388, and 389 trucks equipped with premier trailer hitch assemblies. The pintle hitch assemblies may have been manufactured in a manner resulting in a reduction of fatigue strength of the pivot pins.

Risk. This reduction of fatigue strength could cause the pivot pin to crack and eventually break, causing the trailer to detach from the truck while in motion, which could cause a crash that could result in personal injury or death.

Fix. Dealers will replace the potentially defective pivot pin free of charge. The recall began on april 18, 2008. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Risk. The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.

Fix. Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. On certain trucks equipped with chalmers rear suspensions, the adjustable torque rod end castings may be brittle. A brittle rod end casting may fracture without warning, causing the vehicles' rear axles to become misaligned.

Risk. This misalignment can cause the vehicle to lose directional stability at speeds that may result in a vehicle crash.

Fix. Dealers will inspect the vehicles to determine if they were manufactured with a suspect torque rod end. If a suspect torque rod end is found, the entire torque rod will be replaced. The recall began on october 9, 2006. Owners may contact peterbilt at 1-940-591-4196 or kenworth at 1-425-828-5440.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk. If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Fix. Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

What's wrong. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk. As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Fix. Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.